Various bicycle parts in packaging on a placemat, including handlebars, hydraulic brake housing and handlebar tape.

Continuing the Grand Tradition

When I last replaced Kuroko’s front brake caliper a year ago, I’d cut and recut the hydraulic hose before it all came together, with the result that the hose was pulled quite taut instead of keeping a graceful curve. I figured I’d wait until the Brooks handlebar tape — which was just a year old at that point — was wearing out and due for replacement.

Meanwhile, I’d come across the Deda Gravel handlebars, thanks to James the Shouty Bike Fitter, and put in an order for those after carefully measuring Kuroko’s stock bars. The dimensions are similar in all respects except reach: the Deda bars should bring the brake levers about 25mm closer to the stem, meaning I’ll be sitting a bit more upright and — hopefully — my hands won’t go numb as easily.

When the bars arrived, I ordered replacement hydraulic brake line, and then stopped by the shop where I’d originally bought Kuroko to see what I liked in handlebar tape. I found some textured black tape by fizik that looks pretty cushy.

After removing the Garmin mount, bell and omamori, the tape came off pretty easily, with just a little help from a box cutter. Unlike the Supacaz tape which preceded it, the Brooks tape came off cleanly. The bar end plugs put up more of a fight, and I had to wrestle them out to get the brake levers off.

That feeling when …

Did you ever unintentionally order the super-light carbon fibre parts and not realize it until it came to the weigh-in? No? Just me? Well, I’d have been happy with aluminum but here we are. I doubt 96g is going to make a lot of difference to my performance on the bike. Anyway, they look great.

I’d coincidentally cleaned up my den a couple of weeks ago and come across the internal cable routing kit, and I knew I’d need it for this project. After removing the wheel and brake pads and inserting a brake block, I put some paper towels in a drip pan for the hydraulic fluid and opened the taps. Next I unscrewed the line at both ends. Then with a cable guide attached to one end, I pulled the old hose out of the fork. Pulling the new one back through was nearly as easy with the help of the guide.

Here’s where it becomes a Guy Jean project

I had a lot of room to get the setting tool on the lower end of the brake hose, in contrast to when I’d been replacing the caliper, and I had the barb set after just a bit of fumbling around. I spent some time determining the best length for the new brake hose, making sure it didn’t interfere with the junction box under the handlebar stem and that I’d have some leeway. Finally satisfied, I cut the hose and set the barb.

While I was screwing the hose back into the brake lever, I was concerned it was cross-threading. I backed it out and tried again from the opposite side, and it looked nice and straight. And it was all going nice and smoothly until suddenly … it wasn’t.

Close-up a hydraulic line partially inserted into a brake lever. The portion of the lever where the brake line threads in has snapped off.
Catastrophic failure

The threaded part of the brake lever where the hose screws in has snapped clean off the rest of the body. This is my own mistake coming back to haunt me: five years ago, when I originally installed this Di2 system, I ignored the torque settings so readily visible there at tightened it down with all my might. I don’t know what possessed me to do it except that it looked a bit odd with a gap of a couple of millimeters between the brake housing and the flange on the bolt that secures the brake hose.

Short of gaining access to a foundry and machine shop, there’s no repairing this. I’m glad to say the replacement is available and will be here tomorrow, but of course it’s not cheap. I’m just glad this failure happened in the Workshop in the Sky and not at any point over the past five years while I was riding the bike, kilometers from home and speeding down a hill.

Meanwhile, I’ve still got Hornsby for tomorrow’s ride with José.


Related posts


Posted

in

,

by

Tags:

Comments

2 responses to “Continuing the Grand Tradition”

  1. […] busting the brake lever and making Kuroko unusable on Sunday, I rode Hornsby yesterday to Disneyland. It was an enjoyable […]

  2. […] procrastinated enough on wrapping Kuroko’s new bar tape, a process which started a week ago. I waited this morning for the Workshop in the Sky to warm up a bit, and then continued the […]

Recent posts

Archives

Categories